Optimasi Parameter Bending Vibration Assisted Turning (bvat) Untuk Meminimalkan Surface Roughness Dan Cutting Temperature Dengan Pendekatan Response

Authors

  • Mario Adiprana Muki Telkomuniversity
  • Rino Andias A Telkomuniversity
  • Teddy Sjafrizal Telkomuniversity

DOI:

https://doi.org/10.34818/eoe.v7i2.12439

Abstract

Abstrak Bending Vibration Assisted Turning (BVAT) merupakan sebuah alternatif lanjutan proses pembubutan, dengan memanfaatkan gaya pemotongan yang dibantu dengan menggetarkan tooltip. Penelitian ini bertujuan untuk memodelkan dan menentukan parameter Bending Vibration Assisted Turning (BVAT) yang optimal untuk menghasilkan cutting temperature dan surface roughness yang rendah. Parameter yang dievaluasi adalah spindle speed, feed rate, depth of cut dan frequency pada VAT. Model dikembangkan dengan Response Surface Method (RSM) dari analisis dataset yang diperoleh dari serangkaian percobaan dirancang oleh Box-Behnken Design (BBD). Dalam kasus ini Al6061, respon BVAT yang optimal ditunjukan pada spindle speed 635,991 rpm, feed rate 0,17 mm/rev, frequency 18 KHz dan depth of cut 0,11 mm. Pengaturan tersebut menghasilkan permukaan permesinan baru dengan kekasaran 2,04 µm dan perkiraan suhu pemotongan sebesar 77,1 °C. Kata kunci: bending vibration assisted turning, Al6061, response surface method, box-behnken design. Abstract Bending Vibration Assisted Turning (BVAT) is an alternative advanced turning process, exploiting the cutting force assisted by vibrating the tooltip. This study aims to model and to determine the optimal parameters of Bending Vibration Assisted Turning (BVAT) in producing low cutting temperatures and surface roughness. The evaluated parameters were spindle speed, feed rate, depth of cut, and frequency of the VAT. The model was developed by Response Surface Method (RSM) from analyzing the dataset obtained from a series of experiments designed by Box-Behnken Design (BBD). In the case of Al6061 alloy, the optimal BVAT response was exhibited at spindle speed of 635.991 rpm, feed rate of 0.17 mm/rotation, frequency of 18 KHz, and depth of cut of 0.11 mm. This setup produced a new machined surface with typical roughness of 2.04 μm and an estimated cutting temperature of 77.1° C. Keywords: bending vibration assisted turning, Al6061, response surface method, box-behnken design

Downloads

Download data is not yet available.

References

[1] F. Tjiptono, G. Chandra, and D. Adriana, “Pemasaran Strategik Edisi 3.” ANDI Yogyakarta, Yogyakarta, 2008.

[2] S. Dahbi, H. El Moussami, L. Ezzine, D. Samya, and E. L. M. Haj, “Optimization of turning parameters for surface roughness To cite this version : HAL Id : hal-01260818 Optimization of turning parameters for surface roughness,” 2016.

[3] L. B. Abhang and M. Hameedullah, “Chip-Tool Interface Temperature Prediction Model for Turning Process,” Int. J. Eng. Sci. Technol., vol. 2, no. 4, pp. 382–393, 2010.

[4] M. Mia and N. R. Dhar, “Optimization of surface roughness and cutting temperature in high-pressure coolant-assisted hard turning using Taguchi method,” Int. J. Adv. Manuf. Technol., vol. 88, no. 1–4, pp. 739–753, 2017.

[5] D. E. Brehl and T. A. Dow, “Review of vibration-assisted machining methods for precision fabrication,” Proc. 21st Annu. ASPE Meet. ASPE 2006, no. 6, pp. 2–5, 2006.

[6] V. V. Silberschmidt, S. M. A. Mahdy, M. A. Gouda, A. Naseer, A. Maurotto, and A. Roy, “Surfaceroughness improvement in ultrasonically assisted turning,” Procedia CIRP, vol. 13, pp. 49–54, 2014.

[7] E. Shamoto and T. Moriwaki, “Study on Elliptical Vibration Cutting,” CIRP Ann. - Manuf. Technol., vol. 43, no. 1, pp. 35–38, 1994.

[8] J. Lin, M. Lu, and X. Zhou, “Development of a Non-Resonant 3D Elliptical Vibration Cutting Apparatus for Diamond Turning,” Exp. Tech., vol. 40, no. 1, pp. 173–183, 2016.

[9] P. Zou, Y. Xu, Y. He, M. Chen, and H. Wu, “Experimental investigation of ultrasonic vibration assisted turning of 304 austenitic stainless steel,” Shock Vib., vol. 2015, 2015.

[10] P. G. Benardos and G. C. Vosniakos, “Predicting surface roughness in machining: A review,” Int. J. Mach. Tools Manuf., vol. 43, no. 8, pp. 833–844, 2003.

[11] D. C. Montgomery, Design and Analysis of Experiments (fifth edition), 5th ed., vol. 18, no. 2. New York: John Wiley, 2002.

[12] S. K. Shihab, Z. A. Khan, A. Mohammad, and A. N. Siddiqueed, “RSM based Study of Cutting Temperature During Hard Turning with Multilayer Coated Carbide Insert,” Procedia Mater. Sci., vol. 6, no. Icmpc, pp. 1233–1242, 2014.

[13] A. Kannan, K. Esakkiraja, and M. Nataraj, “Modeling and Analysis for Cutting Temperature in Turning of Aluminium 6063 Using Response Surface Methodology,” vol. 9, no. 4, pp. 59–64, 2013.

[14] A. Agung, S. Nandini, R. A. Anugraha, T. Sjafrizal, M. D. Astuti, and M. R. Ibrahim, “Applying Response Surface Methodology to Optimize the Performance of Longitudinal Vibration-Assisted Turning ( L-VAT ),” vol. 9, no. 07, pp. 916–921, 2020. [Online]. Available: https://www.ijert.org/applying-response-surfacemethodology-to-optimize-the-performance-of-longitudinal-vibration-assisted-turning-l-vat.

[15] G. Ye, L. Ma, L. Li, J. Liu, S. Yuan, and G. Huang, “Application of Box–Behnken design and response surface methodology for modeling and optimization of batch flotation of coal,” Int. J. Coal Prep. Util., no. December 2017, pp. 1–15, 2017.

[16] S. L. C. Ferreira et al., “Box-Behnken design: An alternative for the optimization of analytical methods,” Anal. Chim. Acta, vol. 597, no. 2, pp. 179–186, 2007.

Downloads

Published

2020-08-01

Issue

Pages

5423-5433

Section

Program Studi S1 Teknik Industri

How to Cite

Muki, M. A., A, R. A., & Sjafrizal, T. (2020). Optimasi Parameter Bending Vibration Assisted Turning (bvat) Untuk Meminimalkan Surface Roughness Dan Cutting Temperature Dengan Pendekatan Response. EProceedings of Engineering, 7(2), 5423-5433. https://doi.org/10.34818/eoe.v7i2.12439